-
Notifications
You must be signed in to change notification settings - Fork 10
Test Report (3.1.0)
Vasileios Bimpikas edited this page Feb 15, 2024
·
13 revisions
📝 | This test report applies to versions 3.1.x. Any regressions specific to a .x release will be explicitly noted |
---|
Testing Component | SC598-SOM-EZKIT | SC594-SOM-EZKIT | SC589-EZKIT | SC589-MINI | SC584-EZKIT | SC573-EZKIT |
---|---|---|---|---|---|---|
SRU DAI routing configuration | ||||||
SPORT sending I2S data to CODECs | ||||||
ADAU1761 Audio In Driver | ||||||
ADAU1962 Audio Out Driver | ✅ | ✅ | ✅ | ✅ | ✅ | |
ADAU1979 Audio In Driver | ||||||
ICAP | ||||||
USB Gadget Audio | ✅ | ✅ | ||||
SHARC ALSA | ||||||
remoteproc | ✅ | ✅ | ✅ | |||
virtio rpmsg | ✅ | ✅ | ✅ | |||
Common Clock Framework | ✅ | ✅ | ✅ | ✅ | ✅ | |
Crypto Framework | ➖ | ➖ | N/A | N/A | N/A | N/A |
DMA Peripheral Implicitly tested as it's used by SPI, OSPI, and UART drivers | ✅ | ✅ | ✅ | |||
MDMA Implicitly tested as it's used only by remoteproc to load data to SHARC shared memory | ✅ | ✅ | ✅ | |||
EMAC0 (eth0) | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
EMAC0 (AVB) | ||||||
EMAC11 | ➖ | ➖ | ➖ | ➖ | ➖ | ➖ |
GPIO Control | ||||||
GPTimers | ✅ | ✅ | ✅ | ✅ | ✅ | |
I2C | ✅ | ✅ | ✅ | ✅ | ✅ | |
SRAM/L2 alloc | ✅ | ✅ | ✅ | ✅ | ||
Pin Control Driver | ||||||
RCU driver/system reset | ||||||
SPI | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
QSPI Boot | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
eMMC dev/mmcblk0 | ➖ | N/A | N/A | N/A | N/A | N/A |
eMMC Boot3 | ➖ | N/A | N/A | N/A | N/A | N/A |
SD dev/mmcblk0 | ✅ | N/A | ✅ | ✅ | N/A | ✅ |
SD Boot | ✅ | N/A | ✅ | ✅ | N/A | ✅ |
OSPI4 | N/A | ✅ | N/A | N/A | N/A | N/A |
uart0 | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
USB: Host | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
USB: Device | ✅ | ✅ | ✅ | ✅ | ✅ | ✅ |
Watchdog |
✅: PASS
❗: PASS with warning(s), see note
N/A: Not Applicable
➖: Not Tested
1Currently, the driver can enumerate the IP and identify what is present, but the PHY is not configured/reset yet and so ethernet communications do not work.
2There is a known issue on the SC589-MINI's watchdog which prevents the RCU driver/system from resetting properly
3Currently, booting with the kernel and RFS on SD/eMMC is the only supported configuration, primarily due to hardware limitations on the SOM-CRR-EZKIT (so U-Boot must still be stored on the SPI flash)
4OSPI is not currently working for MX66 chip under 5.15 kernel. OSPI (1S-8S-8S mode) does work for SC594 & IS25LX256