Erlang-In-Docker

Enable Erlang connection among distributed dockers (docker containers on different hosts) by reimplementing the distributed connection protocol of net_kernel.

Introduction

Erlang nodes need connect with each other to work together, so they are usually used in one subnet. However, dockers on different hosts are in different subnets (one subnet per host). So it's difficult to build Erlang cluster on distributed docker cluster.

Erlang Network

When an Erlang node attempts to connect another node, it must create a tcp connection to the node. Because different Erlang nodes listen on different ports, there should be a naming service with a known port which can tell us the port of a Erlang node. That's epmd.

The following figure shows the connection buiding process of Erlang nodes:

Erlang Network in Dockers

Difficulty of Connecting Nodes among Distributed Dockers

It is difficult to connect nodes among distributed dockers, because:

• Dockers on different hosts are in different subnets. If a process in a docker wants to communicate with a process on another docker, it should access the host IP and published host port of the target process.
  
• It is difficult to publish ports used by Erlang node. It is because the port which an Erlang node listens on is allocated dynamically when the node starts.
  
• It is hard to get the published port of an Erlang node. If we use -P or -p xxx:xxx to fix the port mapping, we can start only one docker with Erlang on one host because of port conflict. If we use -p xxx to map the port to an arbitrary host port, we can only get the published port from the docker daemon.
  

Solution

In this project, we implement a new connection protocol module eid_tcp_dist.erl instead of inet_tcp_dist.erl. The following figure shows the new protocol of Erlang connection. We mainly did the following modifications on the connection protocol:

• Limit that each docker can only hold one Erlang node.
  
• Rule that the Erlang node name should be DockerContainerID@HostIP.
  
• Fix the port used by Erlang. (Default 12345)
  
• Use Docker Remote API to get the published port of Erlang node.
  

Install

Docker Configuration

Docker Remote API should be enabled by following steps:

1. add DOCKER_OPTS="-H tcp://0.0.0.0:4243" in /etc/default/docker.io or /etc/default/docker.
   
2. Restart docker daemon by sudo service docker restart.
   

PS: 4243 is the default port used by docker HTTP API. It can also be set to some other value such as 4321, but eid should be configured the same docker port value by adding -kernel docker_dameon_port 4321 when starting Erlang VM.

Erlang-In-Docker Installation, Configuration and Usage

Erlang-In-Docker Installation

You must ensure you have an erlang environment on your computer.

You can compile and install Erlang-In-Docker with the simple command ./build %target_path%, for example:

./build /usr/lib/erlang

After the installation, a complete Erlang environment with eid started automatically is installed to %target_path%.

Erlang-In-Docker Usage

1. You should install Erlang-In-Docker in your docker image, and use new erlang environment installed by Erlang-In-Docker instead of the old one.
   
2. When starting docker, you should add argument -p 12345 to export and publish the port used by Erlang node.
   
3. When starting Erlang node, you should add argument -proto_dist eid_tcp to enable eid_tcp_dist instead of inet_tcp_dist.

PS: 12345 is the default port used by Erlang node. It can also be set to some other value such as 1234, but eid should be configured the same erlang port value by adding -kernel erlang_port 1234 when starting Erlang VM.

For example, the command should be like this:

 sudo docker run -i -t -p 12345 %image_name% /bin/bash
 %target_path%/erl -proto_dist eid_tcp -name [email protected] -setcookie taotaotheripper

PS: asd134fczcv is the container ID, 192.168.4.231 is the IP of the host.

Erlang-In-Docker Configuration

As is mentioned before, when starting Erlang node, you can use kernel envrionment value docker_daemon_port to specify the docker HTTP port Erlang-In-Docker will request, erlang_port to specify the port Erlang node will use in docker. For example:

 # DOCKER_OPTS="-H tcp://0.0.0.0:4321
 sudo docker run -i -t -p 1234 %image_name% /bin/bash
 %target_path%/erl -proto_dist eid_tcp -name [email protected] -setcookie taotaotheripper -kernel docker_daemon_port 4321 erlang_port 1234