Mitsubishi Ecodan Bridge CN105

This software between the Mitsubishi Ecodan FTC controller and a MQTT Broker allows data to be read and commands to be sent.

Hardware

Supported Hardware is ESP8266 ebay sold hardware: https://www.ebay.co.uk/itm/325967595655

M5Stack Atom S3 Lite

Download the files from the /build folder.
Download esptool.exe from Espressif.
Place all the files in the same folder, press and hold the side button of the M5Stack, locate the COM port your M5Stack is on

Open CMD prompt in the folder with the files saved and run:

esptool.exe --chip esp32s3 --port "COM12" --baud 921600  --before default_reset --after hard_reset write_flash -e -z --flash_mode dio --flash_freq 80m --flash_size 4MB 0x0 "ECODAN_Bridge_v5.2.0.bootloader.bin" 0x8000 "ECODAN_Bridge_v5.2.0.partitions.bin" 0xe000 "boot_app0.bin" 0x10000 "ECODAN_Bridge_v5.2.0.bin"

The Pins on the M5Stack are: 1 = Tx, 2 = Rx

Wemos D1 Mini

Download the files from the /build folder.
Download upload.py from Github
Place all the files in the same folder, locate the COM port your Wemos D1 Mini is on

Open CMD prompt in the folder with the files saved and run:

python upload.py --chip esp8266 --port "COM4" --baud "115200" "" erase_flash --before default_reset --after hard_reset write_flash 0x0 "ECODAN_Bridge_v5.2.1_WemosD1.bin"

The Pins on the Wemos D1 Mini are: D0 = Tx, D5 = Rx

Mitsubishi CN105 Protocol Decode

For Ecodan ASHP Units this is the protocol decode information https://gitter.im/Mitsubishi-CN105-Protocol-Decode/community

Physical

Serial, 2400, 8, E, 1

Command Format

Header	Payload	Checksum
5 Bytes	16 Bytes	1 Byte

Header

Sync Byte	Packet Type	Uknown	Unknown	Payload Size
0xfc	Type	0x02	0x7a	Length

Sync Byte

0xfc

Packet Types

Value	Packet Type	Direction
0x41	Set Request	To Heat Pump
0x61	Set Response	From Heat Pump
0x42	Get Request	To Heat Pump
0x62	Get Response	From Heat Pump
0x5A	Connect Request	To Heat Pump
0x5B	Get Request	To Heat Pump
0x7A	Connect Response	From Heat Pump
0x7B	Get Response	From Heat Pump
0x5B	Extended Connect Request	To Heat Pump
0x7B	Extended Connect Response	To Heat Pump

Length

Payload Size (Bytes)

Payload

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
Command	x	x	x	x	x	x	x	x	x	x	x	x	x	x	x	CHK

Checksum

Checksum = 0xfc - Sum ( PacketBytes[0..20]) ;

Set Request - Packet Type 0x41

Available Commands

Active commands so far identified.

Command	Brief Description
0x32	Update Settings
0x34	Hot Water, Holiday and Prohibits
0x35	Thermostat Setpoints

0x32 - Set Options

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x32	Flags	Flags	P	Unk	DHW	HC1	HC2	DHWSP	DHWSP	Z1SP	Z1SP	Z2SP	Z2SP	MRC	MRC	CHK

Flags (2 Bytes) : Flags to Indicate which fields are active
- 0x01 0x00 : Set System Power
- 0x02 0x00 : Unknown (Byte 4) - Operation Mode?
- 0x04 0x00 : Set Hot Water Mode
- 0x08 0x00 : Set Heating Control Mode Zone 1
- 0x10 0x00 : Set Heating Control Mode Zone 2
- 0x20 0x00 : Set Hotwater Setpoint
- 0x40 0x00 : Not Required (uint16)
- 0x80 0x00 : Set Zone 1 Setpoints
- 0x00 0x01 : Not Required (uint16)
- 0x00 0x02 : Set Zone 2 Setpoints
- 0x00 0x04 : Not Required (uint16)
- 0x00 0x08 : MRC Prohibit
- 0x00 0x10 : Not Required (uint16)
P : System Power
- 0x00 : Standby
- 0x01 : Power On
DHW : Hot Water Mode
- 0x00 : Normal
- 0x01 : Eco
HC1 / HC2 : Heating Control Mode Zone 1 / 2
- 0 : Heating Temperature Mode
- 1 : Heating Flow Control Mode
- 2 : Heating Compensation Curve Mode
- 3 : Cooling Temperature Mode
- 4 : Cooling Flow Control Mode
- 5 : Dry Up
DHWSP : Hot Water Setpoint (Temperature * 100)
Z1SP : Zone 1 Setpoint (* 100)
Z2SP : Zone 2 Setpoint (* 100)
MRC Prohibit : (Read 0x26 Byte 14) - MRC Prohibit command must NOT be written to Shizuoka designed models
- 0 : Disable Prohibits
- 8 : Function Set Prohibit
- 32 : Setting Temperature Prohibit
- 64 : Running Mode Prohibit
- 128 : System On/Off Prohibit

0x34 - Hot Water and Holiday Mode

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x34	Flags	Flags	DHW	HOL	IDHW	Z1HI	Z1CI	Z2HI	CZ2I	SCM	Unk1	Unk2	Unk3	Unk4	Unk5	CHK

Flags (2 Bytes) : Flags to Indicate which fields are active
- 0x01 0x00 : Hot Water Force (Boost)
- 0x02 0x00 : Holiday Mode
- 0x04 0x00 : DHW Inhibit (Only When in "Server Control Mode")
- 0x08 0x00 : Heating Z1 Inhibit (Only When in "Server Control Mode")
- 0x10 0x00 : Cooling Z1 Inhibit (Only When in "Server Control Mode")
- 0x20 0x00 : Heating Z2 Inhibit (Only When in "Server Control Mode")
- 0x40 0x00 : Cooling Z2 Inhibit (Only When in "Server Control Mode")
- 0x80 0x00 : Server Control Mode
- 0x00 0x01 : Unused 1 (Byte 11)
- 0x00 0x02 : Unused 2 (Byte 12)
- 0x00 0x04 : Unused 3 (Byte 13)
- 0x00 0x08 : Unused 4 (Byte 14)
- 0x00 0x10 : Unused 5 (Byte 15)
DHW : On (1) / Off (0)
HOL : On (1) / Off (0)
SCM : Server Control Mode On (1) / Off (0)
IDHW : Inhibit DHW On (1) / Off (0)
Unk1 : Unused (Sets 0x28 Byte 11)
Unk2 : Unused (Sets 0x28 Byte 12 - suspected)
Unk3 : Unused (Sets 0x28 Byte 13 - suspected)
Unk4 : Unused (Sets 0x28 Byte 14 - suspected)
Unk5 : Unused (Sets 0x28 Byte 15 - suspected)

0x35 - Set Thermostat Setpoints

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x35	Flags	Flags	CH	Z1SP	Z1SP	Z2SP	Z2SP									CHK

Flags (2 Bytes) : Flags to Indicate which fields are active
- 0x01 0x00 : Cooling/Heating
- 0x02 0x00 : Zone 1 Setpoint
- 0x04 0x00 : Not Required (uint16)
- 0x08 0x00 : Zone 2 Setpoint
- 0x10 0x00 : Not Required (uint16)
- 0x20 0x00 : Unused (Byte 8)
- 0x40 0x00 : Unused (Byte 9)
- 0x80 0x00 : Unused (Byte 10)
- 0x00 0x01 : Unused (Byte 11)
- 0x00 0x02 : Unused (Byte 12)
- 0x00 0x04 : Unused (Byte 13)
- 0x00 0x08 : Unused (Byte 14)
- 0x00 0x10 : Unused (Byte 15)
CH : Cooling (1) /Heating (0)
Z1SP : Zone 1 Setpoint (* 100)
Z2SP : Zone 2 Setpoint (* 100)

0xC9 - FTC Information

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0xC9	0x5F

0x5F: Request

Get Request - Packet Type 0x42

Available Commands

Active commands so far identified, 0x00 to 0xff. Commands not listed appear to generate no resaponse. Some command listed have empty, payload 0x00, response.

Command	Brief Description
0x01	Time & Date
0x02	Defrost
0x03	Refrigerant and Zone Running Information
0x04	Compressor Frequency
0x05	Hot Water Boot Flag
0x06	Unknown - Empty Response
0x07	Output Power
0x08	Unknown - Empty Response
0x09	Zone 1 & 2 Temperatures and Setpoints, Hot Water Setpoint
0x0b	Zone 1 & 2 and Outside
0x0c	Water Flow Temperatures
0x0d	Boiler Flow Temperatures
0x0e	Thermistors 2
0x0f	Thermistors 3 (FTC6+ Only)
0x10	External sources
0x11	Unknown
0x13	Run Hours
0x14	Primary Flow Rate
0x15	Unknown Flags
0x16	Running Pumps
0x17	Unknown - Empty Response
0x18	Unknown - Empty Response
0x19	Unknown - Empty Response
0x1a	Unknown - Empty Response
0x1c	Unknown - Empty Response
0x1d	Unknown - Empty Response
0x1e	Unknown - Empty Response
0x1f	Unknown - Empty Response
0x20	Unknown - Empty Response
0x26	Various Operantion Mode Flags
0x27	Unknown
0x28	Various Operantion Mode Flags
0x29	Zone 1 & 2 Temperatures
0xa1	Consumed Energy
0xa2	Delivered Energy

Payload - All Commands

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
Command	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0

Set Response - Packet Type 0x61

Available Commands

Active commands so far identified.

Command	Brief Description
0x00	OK

0x00 - OK , Command OK, or Just Format?

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
Command	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0	0

Get Response - Packet Type 0x62

Resposes

Responses so far identified.

Command	Brief Description
0x01	Time & Date
0x05	Various Flags
0x09	Zone 1 & 2 Temperatures and Setpoints, Hot Water Setpoint
0x0b	Zone 1 & 2 and Outside Temperature
0x0c	Water Flow Temperatures
0x0d	Boiler Flow Temperatures
0x26	Various Operantion Mode Flags
0x28	Various Operantion Mode Flags
0x29	Zone 1 & 2 Temperatures

0x01 - Time & Date

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x01	Y	M	D	h	m	s

Y: Year
M: Month
D: Day
h: Hour
m: Minute
s: Second

0x02 - Defrost

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x02		R	D	HR?

R: Own Refrigerant Address
D: Defrost
HR: Residual Heat Removal?

0x03 - Refrigerant and Zone Running Information

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x03	RF	F1	F2	F3	F4			M	MF

RF: Refrigerant Flt Code
F1: Fault Code * 100 + Flt Code (F2) (Numbers)
F3: Fault Code (Letter) 1
F4: Fault Code (Letter) 2
M: Multi Zone Running Parameter (3 = Z2 Working, 2 = Z1 Working, 1 = Both Zones working, 0 = Idle)

0x04 - Various Flags

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x04	CF

CF : Compressor Frequency
Slave Frequency in other bytes

0x05 - Various Flags

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x05					DE	HS	HW

DE : Value of 7 given in various running modes
HS : Heat Source (Suspected) 0 = H/P, 1 = IH, 2 = BH, 3 = IH + BH, 4 = Boiler
HW : Hot Water Running Mode (0 = Off, 1 = Heat Pump Phase, 2 = Heater Phase (e.g. Immersion or Booster))

0x07 - Heater Power

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x07				I		P

I : Input Power (kW) - 0 = 0-1kW, 1 = 1-2kW, 2 = 2-3kW etc.
P : Heater Power (to nearest kW)

0x09 - Zone 1 & 2 Temperatures and Setpoints, Hot Water Setpoint

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x09	Z1T	Z1T	Z2T	Z2T	Z1ST	Z1SP	Z2SP	Z2SP	LSP	LSP	HWD	FMx	FMn

Z1T : Zone1 Target Temperature * 100
Z2T : Zone2 Target Temperature * 100;
Z1SP : Zone 1 Flow SetFlow Setpoint * 100
Z2SP : Zone 2 Flow SetFlow Setpoint * 100
LSP : Legionella Setpoint * 100
HWD : DHW Max Temp Drop -40 / 2
FMx : Flow Maximum Temperature -40 / 2
FMn : Flow Minimum Temperature -40 / 2

0x0b - Zone 1 & 2 and Outside Temperature

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x0b	Z1T	Z1T	Z2T	Z2T	?	?		RT	RT	CT	O

Z1T : Zone1 Temperature * 100
Z2T : Zone2 Temperature * 100
RT : Refrigerant Temperature * 100 (Where TH2 is installed)
CT : Condensing Temperature /2 - 40
O : Outside Temp /2 - 40

0x0c - Heater Flow Temps

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x0c	OF	OF		RF	RF		HW	HW		HW2	HW2

OF : Heater Water Out Flow * 100
RF : Heater Return Flow Temperature * 100
HW : Hot Water Temperature * 100 (THW5 or THW5B)
HW2 : Hot Water Temperature * 100 (THW5A if installed)

0x0d - Thermistors 1

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x0d	F1	F1		R1	R1		F2	F2		R2	R2

F1 : Zone 1 Flow Temperature * 100 (Where THW6 installed)
R1 : Zone 1 Return Temperature * 100 (Where THW7 is installed)
F2 : Zone 2 Flow Temperature * 100 (Where THW8 installed)
R2 : Zone 2 Return Temperature * 100 (Where THW9 is installed)

0x0e - Thermistors 2

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x0e	F	F		R	R

F : Boiler Flow Temperature * 100 (Where THWB1 installed)
R : Boiler Return Temperature * 100 (Where THWB2 is installed)

0x0f - Thermistors 3 (FTC6+ Only)

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x0f	M	M		C	C

M : Mixing Tank Temperature * 100 (Where THW10 is installed)
C : Condensing Temperature * 100

0x10 - Hardwired Thermostats

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x10	Z1T	Z2T	OT

Z1T: Hardwired/External (IN1) Thermostat 1 Demand (On/Off)
Z2T: Hardwired/External (IN6) Thermostat 2 Demand (On/Off)
OT: Hardwired/External (IN5) Outdoor Thermostat Demand (On/Off)

0x11 - Dip Switches?

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x10	1		3		4		5		6

Switch 1
Switch 3
Switch 4
Switch 5
Switch 6

0x13 - Run Hours

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x13	U		RH	RH	RH

U : Unknown
RH: Run Hours

0x14 - Immerson/Booster and Primary Flow Rate

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x14		B			I						PF

B : Booster Heater Active
I : Immersion Heater Active
PF : Primary Flow Rate (l/min)

0x15 - Unknown

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x15	PP	U2	U2	P2		TWV	TWV2				U5

PP : Primary Water Pump (Pump 1/OUT1)
U2 : Unknown Int (3+4 Two Bytes?)
P2 : Water Pump 2 (OUT2)
TWV : Three Way Valve Active
TWV2 : Three Way Valve 2 Active (Suspected, if installed)
U5 : Unknown - Always shows 04?

0x16 - Pumps Running

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x16	O4	O3	O13

O4 : Pump 4 (CPN4)
O13 : Pump Output (Out13)
O3 : Pump Output (Out3)

0x26 - Operation Information

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x26			Pwr	OM	HW	OpZ1	OpZ2	HWSP	HWSP	HSP	HSP	SP	SP	??

Pwr - Power
- 0 : Standby
- 1 : On
OM Operation Mode
- 0 : Off
- 1 : Hot Water On
- 2 : Heating On
- 5 : Frost Protect
- 6 : Legionella
HW - Hot Water Mode
- 0 : Normal
- 1 : Economy
Op - Operation Mode (Zone 1 / Zone 2):
- 0 : Heating Temperature Mode
- 1 : Heating Flow Control Mode
- 2 : Heating Compensation Curve Mode
- 3 : Cooling Temperature Mode
- 4 : Cooling Flow Control Mode
- 5 : Dry Up
HWSP : HotWater SetPoint * 100;
HSP : Heating Flow SetPoint * 100;
SP : External Flow SetPoint
?? : 1 for a few cycles when writing to 0x32 byte 14

0x28 - Various Flags

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x28			FHW	HM	HT	PHZ1	PCZ1	PHZ2	PCZ2	SC

FHW : Forced DHW Mode Active
HM : Holiday Mode
HT : Prohibit DHW
PHZ1 : Prohibit Heating Zone1
PCZ1 : Prohibit Cooling Zone1
PHZ2 : Prohibit Heating Zone2
PCZ2 : Prohibit Cooling Zone2
SC : Server Control Mode Active

0x29 - Thermostats

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0x29			HC	Z1T	Z1T	Z2T	Z2T

HC : Heating (0) / Cooling (1)
Z1T : Zone1 Temperature * 100
Z2T : Zone2 Temperature * 100

0xA1 - Consumed Energy

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0xA1	Y	M	D	Heat			Cool			DHW

Y: Year
M: Month
D: Day

0xA2 - Delivered Energy

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0xA2	Y	M	D	Heat			Cool			DHW

Y: Year
M: Month
D: Day

0xC9 - FTC Information

0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
0xC9	U1		U2		U3	V

U1: Version of Protocol (Upper/Lower) BCD
U2: Version of Model (Upper/Lower) BCD
U3: Capacity of Supply
V: FTC Version: 0: FTC2B 1: FTC4 2: FTC5 3: FTC6 5: FTC7 128: CAHV1A 129: CAHV1B 130: CRHV1A 131: CRHV1B 132: EAHV1A 133: EAHV1B 134: QAHV1A 135: QAHV1B 144: PWFY1

Name		Name	Last commit message	Last commit date
Latest commit History 312 Commits
build		build
configuration.yaml examples		configuration.yaml examples
Debug.h		Debug.h
ECODAN_Bridge.ino		ECODAN_Bridge.ino
Ecodan.cpp		Ecodan.cpp
Ecodan.h		Ecodan.h
EcodanDecoder.cpp		EcodanDecoder.cpp
EcodanDecoder.h		EcodanDecoder.h
MQTTConfig.h		MQTTConfig.h
MQTTDiscovery.h		MQTTDiscovery.h
README.md		README.md
TimerCallBack.cpp		TimerCallBack.cpp
TimerCallBack.h		TimerCallBack.h
configuration.yaml		configuration.yaml

F1p/Mitsubishi-CN105-Protocol-Decode

Folders and files

Latest commit

History

Repository files navigation

Mitsubishi Ecodan Bridge CN105

Hardware

Mitsubishi CN105 Protocol Decode

Physical

Command Format

Header

Sync Byte

Packet Types

Length

Payload

Checksum

Set Request - Packet Type 0x41

Available Commands

0x32 - Set Options

0x34 - Hot Water and Holiday Mode

0x35 - Set Thermostat Setpoints

0xC9 - FTC Information

Get Request - Packet Type 0x42

Available Commands

Payload - All Commands

Set Response - Packet Type 0x61

Available Commands

0x00 - OK , Command OK, or Just Format?

Get Response - Packet Type 0x62

Resposes

0x01 - Time & Date

0x02 - Defrost

0x03 - Refrigerant and Zone Running Information

0x04 - Various Flags

0x05 - Various Flags

0x07 - Heater Power

0x09 - Zone 1 & 2 Temperatures and Setpoints, Hot Water Setpoint

0x0b - Zone 1 & 2 and Outside Temperature

0x0c - Heater Flow Temps

0x0d - Thermistors 1

0x0e - Thermistors 2

0x0f - Thermistors 3 (FTC6+ Only)

0x10 - Hardwired Thermostats

0x11 - Dip Switches?

0x13 - Run Hours

0x14 - Immerson/Booster and Primary Flow Rate

0x15 - Unknown

0x16 - Pumps Running

0x26 - Operation Information

0x28 - Various Flags

0x29 - Thermostats

0xA1 - Consumed Energy

0xA2 - Delivered Energy

0xC9 - FTC Information

About

Topics

Resources

Stars

Watchers

Forks

Releases 25

Packages 0

Languages

Packages