1.2.0

The main highlight for this release is the addition of Occupancy Masks! Occupancy masks allow you to define a zone to exclude from detecting motion in, for example if you have a fan and you want to exclude it from triggering the sensor - thanks @MenesesPT and @LarsStegman

Make sure to update to version 1.1.0 of the Everything Presence Lite mmWave Configurator to take advantage of it!

What's Changed

• Bug: Remove fencing for sensors with filters by @MenesesPT in #206
• Fix incorrect update and dashboard URLs by @EverythingSmartHome in #217
• chore: handle zone start and end swapped by @scotttimmins in #216
• Add occupancy mask by @MenesesPT in #218
• Bump version to 1.2.0 by @EverythingSmartHome in #219

Full Changelog: 1.1.1...1.2.0

1.1.1

What's Changed

• Fix max distance for occupancy sensor by @MenesesPT in #193
• Add modular builds for CO2 add-on module by @EverythingSmartHome in #194
• chore: remove an errant if statement by @scotttimmins in #195
• Add CO2 firmware to documentation by @EverythingSmartHome in #196
• Update instructions for CO2 module by @EverythingSmartHome in #197
• Fix zone target count when a zone intercepts 0,0 by @MenesesPT in #199
• Bump version to 1.1.1 by @EverythingSmartHome in #200

Full Changelog: 1.1.0...1.1.1

1.1.0

This release features a re-write of the logic for target tracking and zones, which should resolve an issue where occupancy gets stuck as detected even when there are no targets present under certain circumstances. Thanks @scotttimmins

It also adds a new feature which allows you to configure the installation angle of the sensor (from -45 degrees to +45 degrees) so that zones can now work much better when angled. Thanks @MenesesPT

What's Changed

• Add zone documentation by @EverythingSmartHome in #184
• Fix image names by @EverythingSmartHome in #185
• Feature: Add installation angle by @MenesesPT in #189
• chore: refactor ld2450 lambda by @scotttimmins in #190
• Bump version to 1.1.0 by @EverythingSmartHome in #192

New Contributors

• @MenesesPT made their first contribution in #189
• @scotttimmins made their first contribution in #190

Full Changelog: 1.0.11...1.1.0

1.0.11

What's Changed

• Improve documentation around entities by @EverythingSmartHome in #172
• Bump version to 1.0.11 by @EverythingSmartHome in #181
• Fix false zone trigger by @EverythingSmartHome in #182

Full Changelog: 1.0.10...1.0.11

1.0.10

What's Changed

• Document mmWave sensor firmware update suggestion by @thexperiments in #156
• Add zone target count unit of measure by @figadore in #158
• Update troubleshooting.md by @neilmartin83 in #160
• Revert illuminance calibration by @EverythingSmartHome in #167
• Bump to 1.0.10 by @EverythingSmartHome in #168

New Contributors

• @figadore made their first contribution in #158
• @neilmartin83 made their first contribution in #160

Full Changelog: 1.0.9...1.0.10

1.0.9

What's Changed

• Disable manufacturer update by default by @EverythingSmartHome in #141
• Ensure mmwave is enabled after wifi connection by @EverythingSmartHome in #142
• Bump version to 1.0.9 by @EverythingSmartHome in #143

Full Changelog: 1.0.8...1.0.9

1.0.8

What's Changed

• remove unnecessary fencing interfering with delayed_off by @thexperiments in #117

New Contributors

• @thexperiments made their first contribution in #117

Full Changelog: 1.0.7...1.0.8

1.0.7

What's Changed

• Generate map for the EPL by @obbers in #57
• Set device_class: occupancy for Zone X Occupancy sensors by @golles in #121
• Fix bootloop when internet blocked by @EverythingSmartHome in #122

New Contributors

• @obbers made their first contribution in #57
• @golles made their first contribution in #121

Full Changelog: 1.0.6...1.0.7

1.0.6

This release adds calibration data for the light sensor to drastically improve the readings with the front cover on.

Breaking change

I've marked this as a breaking change, but it's purely because if you have "baseline" numbers in your automations for when the light should come on at a certain lux value, this release will change that baseline figure and will need adjusting.

What's Changed

• Add calibrated values for Light Sensor by @EverythingSmartHome in #116

Full Changelog: 1.0.5...1.0.6

1.0.5

What's Changed

• Add bluetooth control and firmware version to LD2450 by @EverythingSmartHome in #112

Full Changelog: 1.0.4...1.0.5