Skip to content

Latest commit

 

History

History
283 lines (211 loc) · 10.2 KB

index.md

File metadata and controls

283 lines (211 loc) · 10.2 KB
Raw

GitLab Pages administration

Notes:

This document describes how to set up the latest GitLab Pages feature. Make sure to read the changelog if you are upgrading to a new GitLab version as it may include new features and changes needed to be made in your configuration.

Overview

GitLab Pages makes use of the GitLab Pages daemon, a simple HTTP server written in Go that can listen on an external IP address and provide support for custom domains and custom certificates. It supports dynamic certificates through SNI and exposes pages using HTTP2 by default. You are encouraged to read its README to fully understand how it works.

In the case of custom domains (but not wildcard domains), the Pages daemon needs to listen on ports 80 and/or 443. For that reason, there is some flexibility in the way which you can set it up:

  1. Run the Pages daemon in the same server as GitLab, listening on a secondary IP.
  2. Run the Pages daemon in a separate server. In that case, the Pages path must also be present in the server that the Pages daemon is installed, so you will have to share it via network.
  3. Run the Pages daemon in the same server as GitLab, listening on the same IP but on different ports. In that case, you will have to proxy the traffic with a loadbalancer. If you choose that route note that you should use TCP load balancing for HTTPS. If you use TLS-termination (HTTPS-load balancing) the pages will not be able to be served with user provided certificates. For HTTP it's OK to use HTTP or TCP load balancing.

In this document, we will proceed assuming the first option. If you are not supporting custom domains a secondary IP is not needed.

Prerequisites

Before proceeding with the Pages configuration, you will need to:

  1. Have a separate domain under which the GitLab Pages will be served. In this document we assume that to be example.io.
  2. Configure a wildcard DNS record.
  3. (Optional) Have a wildcard certificate for that domain if you decide to serve Pages under HTTPS.
  4. (Optional but recommended) Enable Shared runners so that your users don't have to bring their own.
  5. (Only for custom domains) Have a secondary IP.

DNS configuration

GitLab Pages expect to run on their own virtual host. In your DNS server/provider you need to add a wildcard DNS A record pointing to the host that GitLab runs. For example, an entry would look like this:

*.example.io. 1800 IN A    1.1.1.1
*.example.io. 1800 IN AAAA 2001::1

where example.io is the domain under which GitLab Pages will be served and 1.1.1.1 is the IPv4 address of your GitLab instance and 2001::1 is the IPv6 address. If you don't have IPv6, you can omit the AAAA record.

Note: You should not use the GitLab domain to serve user pages. For more information see the security section.

Configuration

Depending on your needs, you can set up GitLab Pages in 4 different ways. The following options are listed from the easiest setup to the most advanced one. The absolute minimum requirement is to set up the wildcard DNS since that is needed in all configurations.

Wildcard domains

Requirements:

URL scheme: http://page.example.io

This is the minimum setup that you can use Pages with. It is the base for all other setups as described below. Nginx will proxy all requests to the daemon. The Pages daemon doesn't listen to the outside world.

  1. Set the external URL for GitLab Pages in /etc/gitlab/gitlab.rb:

    pages_external_url 'http://example.io'

  2. Reconfigure GitLab

Watch the video tutorial for this configuration.

Wildcard domains with TLS support

Requirements:

URL scheme: https://page.example.io

Nginx will proxy all requests to the daemon. Pages daemon doesn't listen to the outside world.

  1. Place the certificate and key inside /etc/gitlab/ssl

  2. In /etc/gitlab/gitlab.rb specify the following configuration:

    pages_external_url 'https://example.io'

pages_nginx['redirect_http_to_https'] = true
pages_nginx['ssl_certificate'] = "/etc/gitlab/ssl/pages-nginx.crt"
pages_nginx['ssl_certificate_key'] = "/etc/gitlab/ssl/pages-nginx.key"

    where pages-nginx.crt and pages-nginx.key are the SSL cert and key, respectively.

  3. Reconfigure GitLab

Advanced configuration

In addition to the wildcard domains, you can also have the option to configure GitLab Pages to work with custom domains. Again, there are two options here: support custom domains with and without TLS certificates. The easiest setup is that without TLS certificates. In either case, you'll need a secondary IP. If you have IPv6 as well as IPv4 addresses, you can use them both.

Custom domains

Requirements:

URL scheme: http://page.example.io and http://domain.com

In that case, the Pages daemon is running, Nginx still proxies requests to the daemon but the daemon is also able to receive requests from the outside world. Custom domains are supported, but no TLS.

  1. Edit /etc/gitlab/gitlab.rb:

    pages_external_url "http://example.io"
nginx['listen_addresses'] = ['1.1.1.1']
pages_nginx['enable'] = false
gitlab_pages['external_http'] = ['1.1.1.2:80', '[2001::2]:80']

    where 1.1.1.1 is the primary IP address that GitLab is listening to and 1.1.1.2 and 2001::2 are the secondary IPs the GitLab Pages daemon listens on. If you don't have IPv6, you can omit the IPv6 address.

  2. Reconfigure GitLab

Custom domains with TLS support

Requirements:

URL scheme: https://page.example.io and https://domain.com

In that case, the Pages daemon is running, Nginx still proxies requests to the daemon but the daemon is also able to receive requests from the outside world. Custom domains and TLS are supported.

  1. Edit /etc/gitlab/gitlab.rb:

    pages_external_url "https://example.io"
nginx['listen_addresses'] = ['1.1.1.1']
pages_nginx['enable'] = false
gitlab_pages['cert'] = "/etc/gitlab/ssl/example.io.crt"
gitlab_pages['cert_key'] = "/etc/gitlab/ssl/example.io.key"
gitlab_pages['external_http'] = ['1.1.1.2:80', '[2001::2]:80']
gitlab_pages['external_https'] = ['1.1.1.2:443', '[2001::2]:443']

    where 1.1.1.1 is the primary IP address that GitLab is listening to and 1.1.1.2 and 2001::2 are the secondary IPs where the GitLab Pages daemon listens on. If you don't have IPv6, you can omit the IPv6 address.

  2. Reconfigure GitLab

Change storage path

Follow the steps below to change the default path where GitLab Pages' contents are stored.

  1. Pages are stored by default in /var/opt/gitlab/gitlab-rails/shared/pages. If you wish to store them in another location you must set it up in /etc/gitlab/gitlab.rb:

    gitlab_rails['pages_path'] = "/mnt/storage/pages"

  2. Reconfigure GitLab

Set maximum pages size

The maximum size of the unpacked archive per project can be configured in the Admin area under the Application settings in the Maximum size of pages (MB). The default is 100MB.

Backup

Pages are part of the regular backup so there is nothing to configure.

Security

You should strongly consider running GitLab pages under a different hostname than GitLab to prevent XSS attacks.

Changelog

GitLab Pages were first introduced in GitLab EE 8.3. Since then, many features where added, like custom CNAME and TLS support, and many more are likely to come. Below is a brief changelog. If no changes were introduced or a version is missing from the changelog, assume that the documentation is the same as the latest previous version.

GitLab 8.17 (documentation)

  • GitLab Pages were ported to Community Edition in GitLab 8.17.
  • Documentation was refactored to be more modular and easy to follow.

GitLab 8.5 (documentation)

  • In GitLab 8.5 we introduced the gitlab-pages daemon which is now the recommended way to set up GitLab Pages.
  • The NGINX configs have changed to reflect this change. So make sure to update them.
  • Custom CNAME and TLS certificates support.
  • Documentation was moved to one place.

GitLab 8.3 (documentation)

  • GitLab Pages feature was introduced.