How can i adapt the function sendCode() with this output please ?

[belarbi2733]

Der ,

By using rtl_433 -A i have this output :

Analyzing pulses...
Total count: 313, width: 476.27 ms (119067 S)
Pulse width distribution:
[ 0] count: 1, width: 25932 us [25932;25932] (6483 S)
[ 1] count: 192, width: 412 us [404;424] ( 103 S)
[ 2] count: 120, width: 812 us [808;820] ( 203 S)
Gap width distribution:
[ 0] count: 1, width: 34900 us [34900;34900] (8725 S)
[ 1] count: 164, width: 384 us [380;396] ( 96 S)
[ 2] count: 4, width: 3992 us [3992;3996] ( 998 S)
[ 3] count: 140, width: 780 us [776;788] ( 195 S)
[ 4] count: 3, width: 16372 us [16372;16376] (4093 S)
Pulse period distribution:
[ 0] count: 1, width: 60832 us [60832;60832] (15208 S)
[ 1] count: 44, width: 796 us [796;804] ( 199 S)
[ 2] count: 4, width: 4400 us [4400;4404] (1100 S)
[ 3] count: 260, width: 1196 us [1192;1204] ( 299 S)
[ 4] count: 3, width: 16788 us [16788;16792] (4197 S)
Pulse timing distribution:
[ 0] count: 1, width: 25932 us [25932;25932] (6483 S)
[ 1] count: 356, width: 400 us [380;424] ( 100 S)
[ 2] count: 260, width: 796 us [776;820] ( 199 S)
[ 3] count: 1, width: 34900 us [34900;34900] (8725 S)
[ 4] count: 4, width: 3992 us [3992;3996] ( 998 S)
[ 5] count: 3, width: 16372 us [16372;16376] (4093 S)
[ 6] count: 1, width: 100004 us [100004;100004] (25001 S)
Level estimates [high, low]: 15949, 55
RSSI: -0.1 dB SNR: 24.6 dB Noise: -24.7 dB
Frequency offsets [F1, F2]: 1483, 0 (+5.7 kHz, +0.0 kHz)
Guessing modulation: Pulse Width Modulation with sync/delimiter
view at https://triq.org/pdv/#AAB0110701654C0190031C88540F983FF4FFFF8355+AAB05E0703654C0190031C88540F983FF4FFFF91919191919191919191919492A19292A1929292929292A192A1A192A19292A192A192A192929292A1A1A19292A192A192A1A1A1929292A192A1A192A1A192A1A192929292A1A1A1A192A1A1929555+AAB05E0701654C0190031C88540F983FF4FFFF91919191919191919191919492A19292A1929292929292A192A1A192A19292A192A192A192929292A1A1A19292A192A192A1A1A1929292A192A1A192A1A192A1A192929292A1A1A1A192A1A1929655
Attempting demodulation... short_width: 412, long_width: 812, reset_limit: 34904, sync_width: 25932
Use a flex decoder with -X 'n=name,m=OOK_PWM,s=412,l=812,r=34904,g=0,t=0,y=25932'
pulse_slicer_pwm(): Analyzer Device
bitbuffer:: Number of rows: 1
[00] {312} ff fb 7e 96 af 1a 8e 92 78 4f ff ed fa 5a bc 6a 3a 49 e1 3f ff b7 e9 6a f1 a8 e9 27 84 ff fe df a5 ab c6 a3 a4 9e 13

How can i adapt the function sendcode() please ?

Thank you