ESP32-CAM Problem with CAM and SD Card

[matzeeg3]

The Problem

Hi everyone,

i have a problem with a fresh install of AI on the edge:
if i boot up i see the following output:

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
flash read err, 1000
ets_main.c 371 
ets Jun  8 2016 00:22:57

rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:7664
load:0x40078000,len:15360
load:0x40080400,len:3744
entry 0x4008067c
I (27) boot: ESP-IDF 4.3.2 2nd stage bootloader
I (27) boot: compile time 20:02:47
I (27) boot: chip revision: 1
I (30) boot_comm: chip revision: 1, min. bootloader chip revision: 0
I (37) boot.esp32: SPI Speed      : 40MHz
I (42) boot.esp32: SPI Mode       : DIO
I (46) boot.esp32: SPI Flash Size : 4MB
I (51) boot: Enabling RNG early entropy source...
I (56) boot: Partition Table:
I (60) boot: ## Label            Usage          Type ST Offset   Length
I (67) boot:  0 nvs              WiFi data        01 02 00009000 00004000
I (74) boot:  1 otadata          OTA data         01 00 0000d000 00002000
I (82) boot:  2 phy_init         RF data          01 01 0000f000 00001000
I (89) boot:  3 ota_0            OTA app          00 10 00010000 001db000
I (97) boot:  4 ota_1            OTA app          00 11 001f0000 001db000
I (104) boot: End of partition table
I (109) boot_comm: chip revision: 1, min. application chip revision: 0
I (116) esp_image: segment 0: paddr=00010020 vaddr=3f400020 size=4df30h (319280) map
I (247) esp_image: segment 1: paddr=0005df58 vaddr=3ffb0000 size=020c0h (  8384) load
I (250) esp_image: segment 2: paddr=00060020 vaddr=400d0020 size=15e00ch (1433612) map
I (801) esp_image: segment 3: paddr=001be034 vaddr=3ffb20c0 size=029f8h ( 10744) load
I (806) esp_image: segment 4: paddr=001c0a34 vaddr=40080000 size=1c1f4h (115188) load
I (856) esp_image: segment 5: paddr=001dcc30 vaddr=50000000 size=00010h (    16) load
I (871) boot: Loaded app from partition at offset 0x10000
I (871) boot: Disabling RNG early entropy source...
I (883) psram: This chip is ESP32-D0WD
I (883) spiram: Found 64MBit SPI RAM device
I (883) spiram: SPI RAM mode: flash 40m sram 40m
I (888) spiram: PSRAM initialized, cache is in low/high (2-core) mode.
I (895) cpu_start: Pro cpu up.
I (899) cpu_start: Starting app cpu, entry point is 0x40082cbc
I (0) cpu_start: App cpu up.
I (1793) spiram: SPI SRAM memory test OK
I (1801) cpu_start: Pro cpu start user code
I (1801) cpu_start: cpu freq: 160000000
I (1801) cpu_start: Application information:
I (1804) cpu_start: Project name:     esp32cam-server-only
I (1810) cpu_start: App version:      v12.0.1
I (1815) cpu_start: Compile time:     Sep 29 2022 17:14:06
I (1822) cpu_start: ELF file SHA256:  28356ed42df4c694...
I (1828) cpu_start: ESP-IDF:          4.3.2
I (1833) heap_init: Initializing. RAM available for dynamic allocation:
I (1840) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM
I (1846) heap_init: At 3FFC0988 len 0001F678 (125 KiB): DRAM
I (1852) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM
I (1859) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM
I (1865) heap_init: At 4009C1F4 len 00003E0C (15 KiB): IRAM
I (1872) spiram: Adding pool of 4096K of external SPI memory to heap allocator
I (1881) spi_flash: detected chip: generic
I (1884) spi_flash: flash io: dio
I (1894) cpu_start: Starting scheduler on PRO CPU.
I (0) cpu_start: Starting scheduler on APP CPU.
I (1899) spiram: Reserving pool of 32K of internal memory for DMA/internal allocations
=============================================================================================
Branch: 'HEAD', Tag: 'v12.0.1', Revision: dfe2c46, Date/Time: 2022-09-29 17:13
=============================================================================================
I (1929) gpio: GPIO[32]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 
Init Camera
I (3939) gpio: GPIO[25]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:2 
I (3939) cam_hal: cam init ok
I (3939) sccb: pin_sda 26 pin_scl 27
I (3939) sccb: sccb_i2c_port=1

I (3949) gpio: GPIO[32]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 
E (3989) camera: Camera probe failed with error 0x105(ESP_ERR_NOT_FOUND)
E (3989) server_part_camera: Camera Init Failed
Internal Flash-LED turn off PWM
After camera initialization: sleep for : 200ms
I (6009) main: Using SDMMC peripheral
E (6039) sdmmc_common: sdmmc_init_ocr: send_op_cond (1) returned 0x107
E (6039) vfs_fat_sdmmc: sdmmc_card_init failed (0x107).
E (6039) main: Failed to initialize the card (ESP_ERR_TIMEOUT). Make sure SD card lines have pull-up resistors in place.
SD-Card could not be inialized - STOP THE PROGRAMM HERE`

i tried multiple SD Cards, non of all are working. i tryed fat and fat32. with a partion of 1 GB. i also tested a SD card with only 1GB.
So what am i doing wrong. maybe someone can hep me out.

thanks in advance
kind regards
matze

[caco3]

Did you also try another ESP32 board? It really looks like a hardware issue!

[matzeeg3]

so i have the same board running and working with a watermeter. now i want to do the same with a gas meter with the same board. i boght two at the same time from the same seller. but the second get this errors. ok i start with the other board on version 10 can this be the error?

[jomjol]

Camera seems to be broken or not connected. Looks like a hardware topic.

E (3989) camera: Camera probe failed with error 0x105(ESP_ERR_NOT_FOUND)
E (3989) server_part_camera: Camera Init Failed

[matzeeg3]

i just orderd another esp32-cam i keep this topic up to date after it arrives

[matzeeg3]

so i recived my new esp32-cam and it worked out of the box looks like the old one is broken. thanks @jomjol