S.M.A.R.T.

S.M.A.R.T.（Self-Monitoring, Analysis and Reporting Technology）意思是自我监控，分析和报告技术，也常常写成SMART。SMART是计算机硬盘驱动器（HDDs）和固态驱动器（SSDs）的监控系统，用来对许多驱动器可靠性的许多指标进行检测和报告，以便能够预测硬件故障。

当前多数存储设备内建了S.M.A.R.T.附件来监控、存储和分析其设备操作的健康程度。通过软件搜集温度、重新分配的扇区、寻道错误等状态数据，软件可以用来度量设备等健康状况。当S.M.A.R.T.数据预测到驱动器可能的故障，运行在主机上的软件可能会通知用户复制数据到其他驱动器，避免数据丢失以及可以替换驱动器。

本文实践记录是在Inspur（浪潮）SA5212H2服务器上验证，服务器使用了12块 2TB HGST HUS724020AL磁盘 (HGST即日立环球存储技术公司，2011年被西部数据收购)

存储控制器Serial Attached SCSI controller: LSI Logic / Symbios Logic SAS2308 PCI-Express Fusion-MPT SAS-2 (rev 05)

smartmontools

smartmontools软件包包含了2个工具程序来分析和监控存储设备：smartctl和smartd。

设备必须支持SMART功能并且激活每个存储设备的SMART，这样才能有效使用工具。可以使用smartctl来检查是否激活了SMART支持，然后运行测试和检查测试结果。另外，可以使用smartd在自动运行测试和进行email通知。

安装smartmontools

Debian
```
  apt-get install smartmontools
```
CentOS/RHEL
```
  yum install smartmontools
```

smartctl

smartctl是一个命令行工具"控制大多数ATA/SATA和SCSI/SAS硬盘和固态存储内建的SMART"。

--info或-i参数将打印一个设备的信息参数，包括是否支持SMART以及是否激活了该功能。

smartctl -i /dev/sda

显示输出（包括了型号、序列号、Firmware版本、容量、扇区、接口等信息，最后两行参数显示支持SMART）

=== START OF INFORMATION SECTION ===
Device Model:     HGST HUS724020ALA640
Serial Number:    PN2134P6HJG1AP
LU WWN Device Id: 5 000cca 22dd59228
Firmware Version: MF6OAB70
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    7200 rpm
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Tue Feb  2 23:08:43 2016 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

如果设备没有激活SMART，可以使用命令

smartctl --smart=on /dev/sda

有可能需要指定设备类型，如 --device=ata 以便通知smartctl设备类型，避免使用SCSI命令

--smart=off 可关闭设备的SMART功能

运行测试

有3种类型的自我测试（所有的测试都是用户数据安全的）：

short (检查设备的高概率问题)
extended （或者称为long测试，将进行完整的磁盘表面快速检查）
conveyance （在设备的传输过程中标示是否存在损坏）

conveyance 表示"运输"

-c参数（或者--capabilities）输出设备支持的测试以及每个测试需要花费的时间

smartctl -c /dev/sda

输出

=== START OF READ SMART DATA SECTION ===
General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever
					been run.
Total time to complete Offline
data collection: 		(   24) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 317) minutes.
SCT capabilities: 	       (0x003d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

使用-t(或者--test=<test_name>)参数来运行一个测试

smartctl -t short /dev/<device>
smartctl -t long /dev/<device>
smartctl -t conveyance /dev/<device>

查看测试结果

可以使用-H参数来查看设备的健康概况。 "如果设备报告failing health状态，就意味着设备已经故障，或者设备预测自己将在24小时内故障。这种情况下要尽可能快地将设备上的数据导出到安全的存储中"

smartctl -H /dev/<device>

可以列出最近的测试结果以及设备的详细信息

smartctl -l selftest /dev/<device>
smartctl -a /dev/<device>

快速测试案例

启动一个短暂的自测试

sudo smartctl -t short /dev/sda

如果要中断测试（没有必要的话不要自行中断命令）

smartctl -X

短暂自测试大约2分钟，然后用下面的命令查看测试结果

sudo smartctl -l selftest /dev/sda

显示结果类似

=== START OF READ SMART DATA SECTION ===
SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     14591         -
# 2  Short offline       Completed without error       00%     14591         -
# 3  Extended offline    Completed without error       00%         8         -

直接查看磁盘的健康状况

smartctl --health /dev/sda

显示

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

输出详细的设备信息

smartctl -a /dev/sda

输出结果类似

=== START OF INFORMATION SECTION ===
Device Model:     HGST HUS724020ALA640
Serial Number:    PN2134P6HJG1AP
LU WWN Device Id: 5 000cca 22dd59228
Firmware Version: MF6OAB70
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    7200 rpm
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Tue Feb  2 23:30:41 2016 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever
					been run.
Total time to complete Offline
data collection: 		(   24) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 317) minutes.
SCT capabilities: 	       (0x003d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   100   016    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0005   137   137   054    Pre-fail  Offline      -       77
  3 Spin_Up_Time            0x0007   142   142   024    Pre-fail  Always       -       429 (Average 450)
  4 Start_Stop_Count        0x0012   100   100   000    Old_age   Always       -       20
  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   145   145   020    Pre-fail  Offline      -       24
  9 Power_On_Hours          0x0012   098   098   000    Old_age   Always       -       16133
 10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       20
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       666
193 Load_Cycle_Count        0x0012   100   100   000    Old_age   Always       -       666
194 Temperature_Celsius     0x0002   181   181   000    Old_age   Always       -       33 (Min/Max 20/45)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     16133         -
# 2  Short offline       Completed without error       00%     16132         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

smartd

smartd daemon监控SMART状态，并在发生问题时邮件通知。这个服务可以通过systemd管理，并且使用/etc/smartd.conf配置文件。不过这个配置文件非常晦涩难懂，详细配置可以参考 man 5 smartd.conf 或者smartd.conf info

管理smartd服务

启动、检查状态、以及激活自启动和查看最近的日志

systemctl start smartd
systemctl status smartd
systemctl enable smartd
journalctl -u smartd

定义监控的设备

要监控所有可能SMART错误，则配置/etc/smartd.conf（在CentOS 7是/etc/smartmontools/smartd.conf）

DEVICESCAN -a

如果要只监控指定的磁盘，例如

/dev/sda -a
/dev/sdb -a

也可以对外接的磁盘（如通过USB连接的备份用磁盘），需要通知SMARTd设备的UUID，这是因为每次重启设备的/dev/sdX可能变化

要获取需要监控的磁盘的UUID，可以使用ls -lah /dev/disk/by-uuid/ 来查看需要监控的磁盘。以下配置在smartd.conf中的配置就是针对USB磁盘

/dev/disk/by-uuid/820cdd8a-866a-444d-833c-1edb0f4becac -a

使用电子邮件通知潜在的问题

要在故障或新的错误发生时通知，使用-m参数

DEVICESCAN -m address@domain.com

要发送给外部的email地址，需要确保系统有MTA(Mail Transport Agent)或者MUA(Mail User Agent)并且已经正确配置。通常MTU是sendmail和Postfix。

如果设置了-M test就会在smartd服务启动时发送一个测试邮件

DEVICESCAN -m address@domain.com -M test

由于电子邮件投递需要很长时间，而通常期望硬盘故障时立即被通知到以便采取措施。则可以定义执行一个脚本来替代email

DEVICESCAN -m address@domain.com -M exec /usr/local/bin/smartdnotify

CentOS默认配置

检查了CentOS 7默认配置的/etc/smartmontools/smartd.conf，配置内容实际只有一行

DEVICESCAN -H -m root -M exec /usr/libexec/smartmontools/smartdnotify -n standby,10,q

这里通知是发送给系统的root用户，并且执行了脚本 /usr/libexec/smartmontools/smartdnotify 这个脚本实现了email通知，同时将消息写到终端上

#! /bin/sh

# Send mail
echo "$SMARTD_MESSAGE" | mail -s "$SMARTD_FAILTYPE" "$SMARTD_ADDRESS"

# Notify desktop user
MESSAGE="WARNING: Your hard drive is failing"

# direct write to terminals, do not use 'wall', because we don't want its ugly header
for t in $(who | awk '{ print $2; }' | grep -e '^tty' -e '^pts/')
do
  echo "$MESSAGE
$SMARTD_MESSAGE" >/dev/$t 2>/dev/null ||:
done

电源管理

可以用smartd来处理磁盘的低电压模式，这样可以通过smartd来响应SMART命令，磁盘转速。没有这个参数，磁盘可能在低电压情况下仍然高速旋转：

DEVICESCAN -n standby,15,q

详细参考 smartmontools wiki

周期自测

smartd可以告诉磁盘定期执行自检，以下配置设置磁盘每天早上2-3点进行short self-test，在每个周六的早上3-4点进行详细自测

DEVICESCAN -s (S/../.././02|L/../../6/03)

温度改变时告警

smartd可以跟踪磁盘问题并且在磁盘温度太快升高或者达到阀值时高进。以下配置在发生4度温度变化，或者温度达到35度，进行日志，在温度达到40度时日志和邮件告警

DEVICESCAN -W 4,35,40

可以使用命令检查当前磁盘温度 smartctl -A /dev/<device> | grep Temperature_Celsius

完整的`smartd.conf`配置

以下配置将上述所有配置集成

DEVICESCAN (smartd scans for disks and monitors all it finds)

-a (monitor all attributes)
-o on (enable automatic online data collection)
-S on (enable automatic attribute autosave)
-n standby,q (do not check if disk is in standby, and suppress log message to that effect so as not to cause a write to disk)
-s ... (schedule short and long self-tests)
-W ... (monitor temperature)
-m ... (mail alerts)

配置如下

DEVICESCAN -a -o on -S on -n standby,q -s (S/../.././02|L/../../6/03) -W 4,35,40 -m <username or email>

这个配置非常完善，可参考

GSmartControl图形管理工具

GSmartControl是smartctl的的图形前端，显示所有的SMART数值，并且高亮显示那些旧值或者即将故障，可以按照需要运行测试

GSmartControl main window

参考

Wikipedia: S.M.A.R.T.
archlinux: S.M.A.R.T. - 本文主要参考
Monitoring Hard Disks with SMART
Get the disk health status with SMART monitor tools on Debian and Ubuntu Linux
Using smartctl to get SMART status information on your hard drives
ubuntu: Smartmontools - 本文主要参考，提供了监控个人电脑和服务器的脚本以及处理经验
SMART tests with smartctl
Monitoring Hard Drive Health on Linux with smartmontools

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

smart.md

smart.md

S.M.A.R.T.

smartmontools

安装smartmontools

smartctl

运行测试

查看测试结果

快速测试案例

smartd

管理smartd服务

定义监控的设备

使用电子邮件通知潜在的问题

CentOS默认配置

电源管理

周期自测

温度改变时告警

完整的`smartd.conf`配置

GSmartControl图形管理工具

参考

Files

smart.md

Latest commit

History

smart.md

File metadata and controls

S.M.A.R.T.

smartmontools

安装smartmontools

smartctl

运行测试

查看测试结果

快速测试案例

smartd

管理smartd服务

定义监控的设备

使用电子邮件通知潜在的问题

CentOS默认配置

电源管理

周期自测

温度改变时告警

完整的smartd.conf配置

GSmartControl图形管理工具

参考

完整的`smartd.conf`配置